
Dave Wilson, Editor, writes:
We see from your search that you're looking for information on the term "DIP Switches",
and we have a large number of manufacturers' news releases and technical articles here on Engineeringtalk which will be of interest.
Let me be your guide.
Start with
the news release Curtains protect fingers, hands and bodies from
TR Electronic, which we summarised at the time by saying "The Lightbarrier series of safety light curtains conform to IEC61496-1 and IEC61496-2 standards and are classified as Type 4 safety according to EN954-1".
A few weeks before,
we featured the news release Driver handles wide stepper motor range from
US Digital: "The MD2S-P is a conventional step and direction input stepper motor drive while the MD2S-D is a digital speed control version".
In September 2007, we covered the news from Festo
concerning its CMMS-ST motor controller
- take a look at Stepper motors cut costs
which says: "Festo's CMMS-ST controller and EMMS-ST stepper motor combination delivers up to 6.5nm torque and speeds up to 2000rev/min".
Take a look also at the news release from Rockwell Automation, AC drives receive new interface options,
as well as Convertors suit industrial Ethernet from Ethernet Direct,
and Adapter connects devices over network from Westermo Data Communications.
See also:
Serial convertors add reach to RS232
(November 2006)
Serial convertors are a high quality but cost effective option for converting serial signals without any modification to the connected PC's hardware or software
Submersible level transmitter adds adjustment
(October 2006)
The Sensit submersible level/depth transmitter from Roxspur Measurement and Control is used for monitoring boreholes, reservoirs or for groundwater level measurement
Modems overcome industrial interference
(August 2006)
High quality telephone modems provide connection to remote devices and networks reliably within industrial environments and in areas of high level interference
Short-circuit protection couplers
(July 2006)
Trunkguard device couplers provide short-circuit protection for Foundation Fieldbus and Profibus PA devices
Transducer simplifies pneumatic control
(April 2006)
An electropneumatic transducer converts milliamp input signals to a switch-selectable proportional pneumatic output signal, for lower pneumatic supply consumption and reduced operating costs
Relays provide current flow measurement
(August 2005)
A new type of monitoring relay from Carlo Gavazzi provides further protection for generators, by adding current flow measurement to conventional active monitoring
Digital stepper takes power supply onboard
(July 2005)
A new digitally controlled stepper motor driver comes with an integrated 70V power supply
Relays monitor current, voltage and liquid level
(June 2005)
Meeting industry requirements for more precise risk management and more accurate information for reduced maintenance effort, Omron has introduced a new range of monitoring relays
Basic servo solution is a logical step
(June 2005)
The SmartStep is billed as a logical step into basic servo solutions, with an easy to use, highly dynamic combined servo system for point-to-point positioning as part of a motion control process
Machine vision combines visible and near infra-red
(May 2005)
The TM-250/260NIR machine vision camera offers a high-sensitivity interline transfer half-inch CCD imager in a miniature package
Media convertors connect automatically
(March 2005)
JetCon Series industrial serial/Ethernet/fibre media convertors automatically convert serial/Ethernet/fibre signals without any modification to the connected PC's hardware or software
Annunciators overcome plant safety limitations
(February 2005)
A dedicated annunciator offers far greater flexibility than PLCs, DCSs or Scada systems in handling critical plant alarms
Monitor checks machines in hard-to-reach areas
(December 2004)
The latest addition to the successful INA Easy Check range is billed as the perfect solution for monitoring machinery in hard to reach areas
Industrial Ethernet switches support novel rings
(December 2004)
The JetNet Series comprises six different industrial-grade Ethernet switches that support Redundant Super Ring and VLAN/QoS
Industrial Ethernet switch can adapt to one box
(October 2004)
Westermo Data Communications has expanded its industrial Ethernet range with the release of a combined three-port switch and serial-to-Ethernet adapter in a single box
Convertor has the sense to set its datarate
(September 2004)
The EX9520 RS232 to RS485 convertor is part of the Expert EX9000 series of distributed I/O field-to-computer modules for use in industrial environments
V34 modems toughen up for industrial telemetry
(July 2004)
A new range of high quality V34 modems is designed specifically for use in harsh industrial environments
Industrial Ethernet switch breaks price barrier
(May 2004)
The SD-500 series of five-port industrial Ethernet switches meets high industrial specifications and provides very high dependability in harsh environments - but at office Ethernet prices
Plug-and-play operation from budget sensors
(May 2004)
World-Beam QS18FF background suppression sensors are ready to use 'right out of the box'
Industrial ethernet switches feature three ports
(March 2004)
Westermo Data Communications is releasing a new range of industrial ethernet switches designed to provide very high dependability in harsh environmental conditions
Micro-stepper runs like a servo
(February 2004)
The Danaher Motion P7000 micro-stepping drive gives 'servo like' performance without a feedback device
Flexible options for rack-mount UPS system
(November 2003)
Dialog Dual is designed to protect critical computer, telecomms and security applications from mains failures and power fluctuations
New features enhance humidity sensors
(September 2003)
With a new enclosure and a new transmitter ACI has created a humidity line it claims is truly reliable, user friendly and cost competitive
One-piece sensor offers clear visual instructions
(August 2003)
The PVD Series parts verification sensor features large bright green and red job lights that provide distinct visual cues to guide assemblers through a part picking sequence
Timers and counters show their true colours
(August 2003)
A new range of timers and counters feature large reverse-lit liquid crystal displays which can be programmed to change from green to red (or red to green), providing long-range status information
Bridge to analogue signal acquisition
(August 2003)
The WaveAnalog Pro Bridge enables direct connection of strain gauges, load cells and other four-wire resistance measuring devices to control and measurement systems
Encoders turn to multiple uses
(May 2003)
The RHP range of programmable incremental encoders is designed to enable a single encoder to cover multiple applications for the measurement of linear speeds on conveyors, belts, moving webs etc
Annunciator replaces obsolete units
(March 2003)
The Omni30 annunciator has been designed as a replacement for the obsolete RIS UC30 series products
Controller simplifies conveyor installations
(February 2003)
The Allen-Bradley 22ZC zone controller is a groundbreaking new product designed specifically for zero pressure accumulator conveyors
Signal convertor takes control of burners
(July 2002)
A low-voltage signal convertor for interfacing burners with building management systems is the latest innovation to emerge from the product development team at Riello
PID controllers cover full application spread
(May 2002)
A comprehensive range of PID controllers manufactured by Carlo Gavazzi is now available from Vydas International Marketing
Fast factory programming for six-output switcher
(May 2002)
Unipower has introduced a new version of its popular PowerCassette, 1U, 600W, six-output switcher, which has its outputs factory set using internal DIP switches
Flexible functions from counters
(April 2002)
A new range of electronic counters provides convenient and cost-effective solutions for an exceptionally wide range of industrial and commercial counting applications
Timers cover 1 millisecond to well over a year
(January 2002)
A new range of digital timers has just 12 models to cover virtually every requirement, making it unnecessary for users to stock and specify multiple types and models

