Dave Wilson, Editor, writes:
We see from your search that you're looking for information on the term "Supply Voltages",
and we have a large number of manufacturers' news releases and technical articles here on Engineeringtalk which will be of interest.
Let me be your guide.
Start with
the news release Timer and controller range finds UK source from
Dalroad Norslo, which we summarised at the time by saying "European-manufactured timers offer a number of novel features for panel builders".
A few weeks before,
we featured the news release Company helps customers perform relay upgrades from
Pilz Automation Technology: "A small number of PNOZsigma relays are replacing a very wide range of Classic relays, which will significantly simplify ordering and stockholding for customers".
In October 2007, we covered the news from Lenze
concerning its SMD drives
- take a look at Drives suit compressed air systems
which says: "The IceTech range of blasting equipment employs a high-pressure pump powered by a single three-phase 230V 50Hz motor to propel the dry ice pellets into a compressed air stream".
Take a look also at the news release from TR Controls, Small positioning drive offers low cost,
as well as Stepper motors cut costs from Festo,
and Soft starter feature new torque technology from WEG Electric Motors (UK).
See also:
Drives and servomotors chosen for printing machine
(August 2007)
Pringint of corrugated board requires both fast dynamic response and high precision from the servo equipment
Position transducers suit tough environments
(July 2007)
Macro Sensors' HSI/R 750 series of hermetically sealed, loop-powered 4-20mA position transmitters is designed for mechanical position measurement where a hard connection can be made to a test piece
Positioning drive automates change-over
(July 2007)
The MD 300 is suitable for automating change-over and adjustment procedures, reducing down-time and significantly raising machine productively
Outdoor radio transmits up to 3km
(June 2007)
The Europipe radio module can be installed outdoors without additional switching cabinets and are easy to install
Power control modules save weight and costs
(May 2007)
Block's PowerVision power control modules were developed for applications where an IEC61131-2 compliant output voltage is satisfactory
Accelerometers suit automotive applications
(March 2007)
The 2260 range is designed as a cost-effective replacements to piezorestive accelerometers, but with higher accuracy levels
The changing face of industrial timers
(March 2007)
Modern timers have been designed to allow clear defined operation but with a range of auxiliary circuits to offer the user a wide range of functions to give as much flexibility as possible
Regenerative power modules retrieve braking energy
(February 2007)
Siemens Automation and Drives (AandD) has now added the PM250 and PM260 regenerative power modules to its Sinamics G120 range of frequency inverters
Compact air circuit breakers are quick to retrofit
(December 2006)
A new range of low voltage air circuit breakers has been launched by Mitsubishi Electric
Industrial modems mount the rail
(September 2006)
The Telemodem2 family is now available with DIN-rail fixings
Drives optimise food process pumping efficiency
(August 2006)
Lenze smd drives have been specified by Seepex pumps for supply with its range of innovative progressive cavity pumps
AC drives add flexibility to pressing tasks
(August 2006)
Lenze smd drives have been used to provide accurate variable speed control for the world-famous Electrolux range of industrial ironing machines
Machinery safety standard is revised
(July 2006)
Machinery designers, developers, manufacturers, installers and service engineers need to comply with the requirements set out in the Machinery Directive 98/37/EC
Latest guidance on Machinery Safety
(July 2006)
Machinery designers, developers, manufacturers, installers and service engineers need to comply with the requirements set out in the Machinery Directive 98/37/EC
Controller keeps watch over bucket elevators
(May 2006)
The 4B Watchdog Elite uses noncontact magnetic sensors to monitor belt speed and belt alignment at the head/boot or both
DC drives are easy to install
(April 2006)
DC drive controllers have guided commissioning included as standard, which means the drive can be installed by the user, in most cases without reference to the manual
Interface options added to graphics printers
(March 2006)
Graphics printers for printing measured data, status and fault reports in instrumentation, automation and industrial process applications
Brochure details temperature transmitter equipment
(February 2006)
Brochure provides information about analogue and intelligent temperature transmitter equipment, including operating parameters, certificates, supply voltages and output signals
See SAW measure torque
(December 2005)
Sensor Technology adds two non-contact torque sensors to its Torqsense range
Smart relay manages up to three alternating pumps
(October 2005)
Carlo Gavazzi UK is expanding its portfolio of products for the water treatment market with the introduction of a new pump changeover relay
Test supply offers analogue and digital control
(October 2005)
A versatile switch-mode AC power supply unit provides a stepless adjustment of output voltage and frequency, with a choice of either analogue or digital control
Gear-tooth sensors promise high reliability
(October 2005)
A new family of AC-coupled Hall-effect gear-tooth sensors combine a compact package size with integrated filter capacitors to provide additional reliability
Inline amplifier is complete LVDT solution
(October 2005)
A new compact version of the popular S7AC LVDT inline amplifier contains all the required circuitry to excite, condition and amplify the transducer
Printers put graphics on the panel
(September 2005)
The recently launched IPP 144-40G/GE range of Gossen, Muller and Weigert graphics panel printers, supplied by Metrix Electronics, are now available from RS Components worldwide
Uninterruptible supplies are made for industry
(July 2005)
A new family of DIN mounted, line interactive uninterruptible power supplies is designed to protect industrial processes from the potentially disastrous effects of power disruptions
Terminal boxes go low profile
(March 2005)
The ME MAX line of housings from Phoenix Contact now includes low-profile designs ME MAX Flat and ME MAX Superflat
Italian drives step in to control
(February 2005)
New from Total Motion Systems are the Mind B and Mind T series stepper drives manufactured by RTA Italy
Encoder aids simple speed and position control
(January 2005)
The DKS 40 incremental encoder has a compact design, which features a robust dustproof construction and protection to IP64
Welding supply takes service system onboard
(January 2005)
The 165C Basic orbital welding power supply incorporates a revolutionary system that makes on-site operator maintenance a reality for the first time
Easy interfacing for panel-mounting printers
(November 2004)
Metrix Electronics' IPP 144-40G panel printers feature fast, long-life, fixed-head, thermal mechanisms to print graphics, text or barcodes on 80mm wide 'document proof' thermal paper
Combined beacon and sounder uses little power
(November 2004)
A new ISB range of compact, IP65, low-current, combined flashing beacon and sounder units is being launched by DG Controls
Modem mounts the rails
(October 2004)
The rugged Telemodem2 modem is ideal for remote industrial plant monitoring and is now available with DIN-rail fixings
Speed sensor turns to automotive crankshafts
(September 2004)
The A1425 is a high-accuracy analogue Hall-effect speed sensor IC with an integrated tracking capacitor and a dual zero-crossing output signal
Soft-start sizing and programming made simple
(August 2004)
WEG is increasing both the functionality and ease of use of its SSW-05 micro soft-starters with the introduction of a new programmable keypad and sizing software