Delcam adds options for Powerinspect software
A
Delcam product story
Edited by the Engineeringtalk editorial team
Oct 29, 2009
Delcam has added two new options for its Powerinspect inspection software.
Powerinspect Partaligner can be used with portable inspection equipment to simplify setup operations for machine tools.
It is similar to the automated position compensation provided by NC-Partlocator for machine tools with probing systems but uses a separate measuring device.
Powerinspect Tubing makes it easier to inspect pipework and tubing, according to the company.
Both of the options are intended to increase the range of applications for Powerinspect.
Partaligner uses the alignment functionality from Powerinspect to find exactly where a part is located on a machine tool from a series of measurements.
It will normally be used with a portable inspection device positioned on or beside the machine.
This will typically be an inspection arm for medium-sized components or an optical device for very large tooling.
The measured position is then compared with the datum used in the computer-aided-manufacturing (CAM) system to program the component.
The results can be used to update a project in Delcam's Powermill CAM system by adjusting the datum position and orientation.
Alternatively, the data can be applied directly to change the offsets in the machine-tool control so that they reflect the measured position of the component rather than the nominal value in the programming software.
Using Partaligner with an independent inspection device overcomes any concerns that might arise from using a machine tool to check its own performance.
It is also flexible as the same inspection equipment can be used on a number of machine tools, in addition to its normal inspection duties.
However, an extra step is needed when setting up the system: each time the device is moved, it must be referenced against an item with known machine-tool coordinates before being used to measure the part position.
The main benefit is in reducing the time and variability associated with the fine manual adjustment of the part setup.
Partaligner allows independent inspection to be carried out and positional problems to be corrected much more quickly and easily, especially with larger and heavier parts.
The new Powerinspect Tubing module makes it easier to inspect tubing and pipes, especially when these are part of a larger assembly, according to Delcam.
Specialist software is available for tubing inspection but this does not generally allow the measurement of other types of geometry, so two different and potentially incompatible systems may be required.
Powerinspect Tubing makes it easier to inspect this specialised pipe geometry together with other components using a single software program.
The Tubing module can be used on the full range of inspection equipment supported by the main Powerinspect program, including manual and CNC CMMs, inspection arms and other portable devices.
To operate the Tubing module, the user enters the number of straight sections and their points of intersection.
The other features and nominal values are automatically calculated.
The module creates the overall design within Powerinspect and sets the nominal values to be measured.
The inspection can then be undertaken as usual.
The main applications for the module are expected to be for portable inspection solutions used in the oil-and-gas industry, where pipework is often combined with other components.
Not what you're looking for? Search the site.
Contact Delcam
Tel +44 121 683 1081
Other Delcam stories
-
Delcam seminar addresses composites in aerospace
Delcam is to host a free seminar on composites in aerospace at its Birmingham headquarters on 25 November. -
Delcam to demonstrate CAD/CAM machinery solutions
Delcam will showcase its Powershape computer-aided-design (CAD) software at the CADCAM Matters organised by the Machinery magazine, taking place at Donington Park on 18 November. -
Software offers multiple modelling techniques
Having all the different modelling techniques in a single package reduces the need to transfer data between multiple programs and so streamlines the whole product development process -
CAD software receives press design update
Delcam Toolmaker CAD software's deep-draw press tool design updates shorten design time by providing dedicated functionality for many of the tasks involved in preparing the tooling. -
Educational CAD software explained in podcasts
Training programme comprises 27 tutorials, covering all stages from basic sketching through to solid and surface modelling.
Browse by category
-
Capital Equipment (3,515)
- Capital Equipment (1)
- Compressors and Air Treatment (538)
- Electrical hardware (131)
- Electronics Manufacturing, Tools, Instruments (192)
- Machinery and Production Equipment (1,131)
- Manufacturing Machinery and Plant Equipment (474)
- Production line blowers and fans (74)
- Robotics, Handling and Storage (974)
- Consultancy and Services (922)
-
Control and Instrumentation (5,125)
- Cabling, Conduit, Signal Conditioning (816)
- CNC and Motion Controllers (189)
- Control and Instrumentation (3)
- HMIs/Operator Interfaces (296)
- Logic Controllers, Timers and Relays (96)
- Mid-range and Large PLCs (203)
- Plant- and Machine-Wide Communications (1,203)
- Plantwide control (1,352)
- Power Supplies, Uninterruptible Power (575)
- Smaller-Sized PLCs (392)
-
Drives, Motors and Controls (3,436)
- Drives, Motors and Controls (2)
- Industrial Drives/Controls (1,290)
- Industrial Motors (501)
- Linear Drives and Motors (121)
- Precision Motors and Gears (430)
- Stepper and Servo Drives, Motors, Controls (1,090)
-
Electrical and Electronic Equipment Design (4,305)
- Batteries, chargers and circuit protection (583)
- Connectors, Terminals, Busbars, Slip Rings (717)
- Electrical and Electronic Components (649)
- Electrical and Electronic Equipment Design (3)
- Electrical and Electronic Subassemblies (375)
- Enclosures and Equipment Cooling Fans (722)
- Knobs, Handles and Enclosure Hardware (430)
- PCs and Embedded Systems (826)
-
Engineering Design Software (6,361)
- 2D CAD software (203)
- 3D CAD software (1,191)
- CAM, CNC, production management software (583)
- Data, document management software (322)
- Electrical design software (167)
- Engineering Design Software (17)
- FEA and structural analysis software (376)
- File conversion software, data capture (358)
- Fluid, thermal, noise, vibration software (339)
- Materials design and moulding design software (152)
- Maths, charting, statistics, QA software (325)
- PLM and collaboration software (664)
- Process, instrumentation, automation software (269)
- Publishing and documentation software (234)
- Rendering, visualisation, styling software (206)
- Simulation, modelling, validation software (955)
-
Engineering Industry News, Resources (6,211)
- Electronic Resources for Engineers (278)
- Engineering Business News, Views (388)
- Engineering Conferences (438)
- Engineering Education, Resources, Standards (850)
- Engineering Exhibitions, Events (577)
- Engineering Guides, Newsletters (366)
- Engineering Industry Developments, Awards (636)
- Engineering Industry News, Resources (4)
- Engineering Industry Reports, Surveys (597)
- Engineering Recruitment, Employment (219)
- Engineering Seminars (418)
- Engineering Training Courses (457)
- Health and Safety Consultancy, Software (180)
- Health and Safety Events, Training, News (285)
- Health and Safety Legislation (403)
- Health and Safety Strategy, Risk Assessment (115)
- Machine Building (4,621)
-
Materials and Processing (3,030)
- Materials and components (2,267)
- Materials and Processing (5)
- Materials processing and testing (291)
- Rapid Prototyping (467)
-
Monitoring, Measurement and Quality (5,648)
- Data Acquisition Hardware and PC I/O Boards (489)
- Data acquisition Software and Communications (505)
- Data loggers (425)
- Electrical and Electronic Testing, PAT Equipment (643)
- Form/co-ordinate, optical, vision instruments (762)
- Gauges, Indicators and Instruments (449)
- Materials testing equipment (431)
- Monitoring, Measurement and Quality (1)
- Telecomms/network test equipment, software etc (158)
- Testing and Calibration Services and Information (518)
- Testing, analysing and monitoring equipment (1,267)
-
Powertrain Design (3,711)
- Bearings (983)
- Chains and belts (333)
- Gears, brakes, couplings and engines (1,475)
- Hydraulic Components (475)
- Lubricants (441)
- Powertrain Design (3)
-
Sensors (7,278)
- Accelerometers and Vibration Sensors (448)
- Barcode Sensors (103)
- Flowmeters and Flow Sensors (643)
- Gas, Chemical, Radiation, Magnetic Sensors (290)
- Humidity and Environmental Sensors (158)
- Level Sensors and Leak Detectors (538)
- Linear Position Sensors (413)
- Loadcells, Force Sensors, Torque Sensors (728)
- Pressure sensors (639)
- Proximity Sensors (713)
- Rotary Position, Tilt and Angular Sensors (563)
- Sensors (11)
- Temperature sensors (621)
- Vision and Colour Sensors (1,410)
- Small Mechanical Components, Joining, Tools (2,041)
- Valves, Pumps, Process Hardware (3,723)
