Motors and diaphragms boost pump performance

Hargraves Technology has achieved breakthrough advances in brushless DC motors and diaphragm elastomer materials.

Miniature diaphragm pumps have had their performance and operational life limited by standard elastomer mechanical properties and DC brushless motor designs.

As fluidic system developers have demanded smaller component envelopes, diaphragm pumps have incurred increased challenges to increase performance and life requirements.

Hargraves Technology has achieved breakthrough advances in brushless DC motors and diaphragm elastomer materials.

The Hargraves BTC, CTS and LTC series of miniature diaphragm pumps offer a series of brushless DC motor driven pumps, vacuum pumps and compressors to handle air, gases and several liquid applications.

The Hargrave innovative designs and advanced fluidic technolgies offers the highest performance in the smallest package size available.

These diaphragm pump series uses a proprietary advanced diaphragm elastomer (AEPDM) and superior brushless motor design to set the highest benchmark for service-free miniature diaphragm pump operation that exceeds 20,000 hours.

Brushless DC motors (BLDC) developed by Hargraves are designed to endure long life applications to achieve high reliability and performance under challenging operational loads.

The Hargraves engineering team took the initiative to improve standard motor designs and manufacturing processes to optimise efficiencies and endurance.

Both a "short stack" and "long stack" configurations were produced for different torque requirements.

The long stack brushless DC motor, for instance, consists of magnets and windings that are twice the length and is used for exceptionally high load applications.

Brushless motors, as the name implies, do not use brushes for commutation.

Instead, they are electronically commutated.

The stator consists of stacked steel laminations that are axially cut along the inner periphery.

Numerous coils are interconnected to form each winding.

An even number of magnetic poles are produced from each of these windings that are distributed over the stator periphery.

The rotor is a permanent magnet with alternating magnetic poles built in.

To rotate a DC motor, the windings need to be energised in sequence.

The position of the rotor will determine which winding will need to be energised.

Unlike brush motors that commutate by mechanical switching, brushless motors position using an electronic sensorless method or by utilising Hall effect sensors.

These sensors are embedded on the stationary part of the motor and monitor the exact position on the rotor's position.

As the rotor's magnetic poles rotate near the Hall effect sensors, they give a high or low signal that signifies a north or south pole is passing near the sensors.

The exact sequence of commutation can be determined from the combination of the three signals the sensors are reading.

Each commutation sequence has current entering one of the windings resulting in positive magnetic flow, current exiting a second winding resulting in a negative magnetic flow, and a third winding that would be nonenergised.

The direction of the magnetic flow would affect the winding's polarity.

The interaction of these changing poles of the magnetic field between the stator and the permanent motor produces the torque that turns the motor's shaft.

As the requirements for miniature diaphragm pumps to fit in even smaller package envelopes, the motors powering these systems have had to become smaller.

These smaller brushless motor sizes will most likely use sensorless commutation methods since Hall effect sensors take up more space.

It should be noted that sensorless motors are limited to the initial startup torque they can produce.

Brushless DC motor applications that require restarts under a high load will need to use Hall effect sensors with an instant start capability.

Therefore, to achieve very small motor size, there may need to be a tradeoff on restart capabilities.

Current diaphragm elastomers are limited to only a few thousand hours since they are unable to withstand the increased temperatures and demanding mechanical stresses.

As a result, it is common for diaphragm pump manufacturers to require replacement kits to extend life.

The proven track of service free performance reduces the overall costs for an OEM's product.

The innovative and efficient engineering design enables the Hargraves series of micro and miniature diaphragm pumps and compressors to push the performance envelope in a lightweight, compact size achieving the highest performance/size ratio of current technology miniature diaphragm pumps and compressors.

The selection of advanced materials and innovative elastomer diaphragm geometries facilitates the Hargraves miniature diaphragm pumps to operate in increased temperature environments up to 70C.

The optimised pump head, chamber and flow path reduce noise without compromising performance.

Back to top