Gearbox monitoring system reduces downtime
A
Schaeffler (UK) product story
Edited by the Engineeringtalk editorial team
Oct 21, 2009
The Praxis condition monitoring partnership between CNES and Schaeffler UK has enabled Corus engineers at a beam mill in Teesside to oversee an internal redesign to the hot saws gearbox.
In 2006, an FAG Dtect X1 online remote monitoring device was installed on the hot saws to determine their condition.
An online remote monitoring device was installed on the hot saws at the beam mill in Lackenby to determine the condition of the saws
The hot saws consist of two circular saws, one fixed and one moving, which cut through H-section beams of hot steel as they exit the beam mill.
The online monitoring device soon highlighted problems that had previously gone unnoticed.
As well as imbalances to the saw blades, it also detected bearing and lubrication problems within the gearbox.
The Dtect X1 system has been monitoring this critical piece of machinery for more than two years and has provided the plant engineers at Corus with trending information on the condition of the gearbox.
It soon became apparent that there were inherent design faults within the gearbox itself that were causing regular bearing failures.
'We have been experiencing failures on our gearboxes for a number of years now,' said Steve Bowman, the beam mill's manufacturing engineer in charge of the hot saws and finishing equipment.
'By using the Dtect X1 system from Schaeffler, we've been able to pinpoint the exact source of these failures,' he added.
With the help of Paul Harrison from the PCM team, Bowman was able to single out bearing C within the gearbox as the root cause of failure.
'The readings we were getting from the Dtect X1 device showed us that there was an issue with bearing C,' said Bowman.
'The bearing was running hot right from the start, so we experimented with the bearing clearances and looked at the lubrication system.
'We noticed that bearing C was suffering from oil starvation, so oil was diverted from bearing D.
'By doing this, the running temperature of the bearing improved substantially,' he added.
However, even though the bearings had been replaced and the lubrication system had been improved, the gearbox was still failing.
Following discussions with a transmission consultant, it soon became clear that this bearing was right at the edge of its design capabilities.
Because the gearbox was prone to continual bearing failure, Bowman challenged the consultant to come up with a new internal design that would eliminate bearing failure.
Using the data from Dtect X1, the existing gearbox has since been modified to include a new bearing arrangement and lubrication system.
By keeping the same gearbox casing, Corus is now able to easily interchange the existing two gearboxes and avoid the cost of a new one, which is around GBP110,000.
'What the Dtect X1 system allowed us to do was gain valuable experience and time,' said Bowman.
'Not only did we know that there was a problem, but we also knew the degree of the problem.
'It gives us the confidence to run the gearbox until the next planned outage, knowing that we won't have a catastrophic gearbox failure on our hands and that we will have everything in place to make a planned change if required,' he added.
The Dtect X1 device has allowed Corus engineers to improve their plant preventative maintenance regime.
With the information they have gathered in recent months, they have also been able to work with the saw blade manufacturers to ensure that the blades are balanced to a much higher degree than previously supplied.
Not what you're looking for? Search the site.
Contact Schaeffler (UK)
Tel +44 121 351 3833
Other Schaeffler (UK) stories
-
FAG Dtect prevents power-turbine failure at Corus
An FAG Dtect X1 online vibration-monitoring system has prevented the failure of a steam turbine at a Scunthorpe Corus plant, and in doing so has saved thousands of pounds in lost power generation. -
Schaeffler offers compact FAG wheel bearings
The Schaeffler Group's range of FAG wheel bearings is more compact, lighter and offers simplified mounting via a self-centring, axial spur-gear teeth design. -
Guide advises on mounting and dismounting bearings
Schaeffler UK has published a technical guide entitled 'Mounting and Dismounting of Rolling Bearings'. -
Split bearings provide reduced maintenance costs
Pilbara Iron has achieved significant cost savings by replacing a standard spherical roller bearing on the drive shaft of a bucket wheel excavator with a split roller bearing from Schaeffler. -
Fiat orders mechanical tappets from Schaeffler
Schaeffler's automotive manufacturing plant in Llanelli, Wales, has received an order for the supply of 11 million mechanical tappets from Italian car company Fiat.
Browse by category
-
Capital Equipment (3,532)
- Capital Equipment (1)
- Compressors and Air Treatment (545)
- Electrical hardware (131)
- Electronics Manufacturing, Tools, Instruments (192)
- Machinery and Production Equipment (1,133)
- Manufacturing Machinery and Plant Equipment (478)
- Production line blowers and fans (74)
- Robotics, Handling and Storage (978)
- Consultancy and Services (927)
-
Control and Instrumentation (5,141)
- Cabling, Conduit, Signal Conditioning (818)
- CNC and Motion Controllers (190)
- Control and Instrumentation (3)
- HMIs/Operator Interfaces (297)
- Logic Controllers, Timers and Relays (96)
- Mid-range and Large PLCs (204)
- Plant- and Machine-Wide Communications (1,209)
- Plantwide control (1,354)
- Power Supplies, Uninterruptible Power (577)
- Smaller-Sized PLCs (393)
-
Drives, Motors and Controls (3,449)
- Drives, Motors and Controls (2)
- Industrial Drives/Controls (1,292)
- Industrial Motors (502)
- Linear Drives and Motors (121)
- Precision Motors and Gears (434)
- Stepper and Servo Drives, Motors, Controls (1,096)
-
Electrical and Electronic Equipment Design (4,324)
- Batteries, chargers and circuit protection (587)
- Connectors, Terminals, Busbars, Slip Rings (723)
- Electrical and Electronic Components (652)
- Electrical and Electronic Equipment Design (4)
- Electrical and Electronic Subassemblies (377)
- Enclosures and Equipment Cooling Fans (722)
- Knobs, Handles and Enclosure Hardware (430)
- PCs and Embedded Systems (829)
-
Engineering Design Software (6,385)
- 2D CAD software (203)
- 3D CAD software (1,199)
- CAM, CNC, production management software (583)
- Data, document management software (324)
- Electrical design software (167)
- Engineering Design Software (17)
- FEA and structural analysis software (377)
- File conversion software, data capture (358)
- Fluid, thermal, noise, vibration software (339)
- Materials design and moulding design software (153)
- Maths, charting, statistics, QA software (325)
- PLM and collaboration software (665)
- Process, instrumentation, automation software (269)
- Publishing and documentation software (234)
- Rendering, visualisation, styling software (208)
- Simulation, modelling, validation software (964)
-
Engineering Industry News, Resources (6,199)
- Electronic Resources for Engineers (273)
- Engineering Business News, Views (388)
- Engineering Conferences (438)
- Engineering Education, Resources, Standards (851)
- Engineering Exhibitions, Events (578)
- Engineering Guides, Newsletters (354)
- Engineering Industry Developments, Awards (635)
- Engineering Industry News, Resources (4)
- Engineering Industry Reports, Surveys (597)
- Engineering Recruitment, Employment (219)
- Engineering Seminars (421)
- Engineering Training Courses (458)
- Health and Safety Consultancy, Software (180)
- Health and Safety Events, Training, News (285)
- Health and Safety Legislation (403)
- Health and Safety Strategy, Risk Assessment (115)
- Machine Building (4,630)
-
Materials and Processing (3,040)
- Materials and components (2,271)
- Materials and Processing (5)
- Materials processing and testing (292)
- Rapid Prototyping (472)
-
Monitoring, Measurement and Quality (5,680)
- Data Acquisition Hardware and PC I/O Boards (491)
- Data acquisition Software and Communications (505)
- Data loggers (428)
- Electrical and Electronic Testing, PAT Equipment (645)
- Form/co-ordinate, optical, vision instruments (765)
- Gauges, Indicators and Instruments (449)
- Materials testing equipment (439)
- Monitoring, Measurement and Quality (1)
- Telecomms/network test equipment, software etc (159)
- Testing and Calibration Services and Information (522)
- Testing, analysing and monitoring equipment (1,276)
-
Powertrain Design (3,723)
- Bearings (986)
- Chains and belts (334)
- Gears, brakes, couplings and engines (1,482)
- Hydraulic Components (475)
- Lubricants (441)
- Powertrain Design (4)
-
Sensors (7,313)
- Accelerometers and Vibration Sensors (450)
- Barcode Sensors (103)
- Flowmeters and Flow Sensors (649)
- Gas, Chemical, Radiation, Magnetic Sensors (293)
- Humidity and Environmental Sensors (158)
- Level Sensors and Leak Detectors (539)
- Linear Position Sensors (417)
- Loadcells, Force Sensors, Torque Sensors (732)
- Pressure sensors (642)
- Proximity Sensors (715)
- Rotary Position, Tilt and Angular Sensors (564)
- Sensors (12)
- Temperature sensors (623)
- Vision and Colour Sensors (1,416)
- Small Mechanical Components, Joining, Tools (2,057)
- Valves, Pumps, Process Hardware (3,730)
