Click on the advert above to visit the company web site

Product category: Smaller-Sized PLCs
News Release from: Mitsubishi Electric Automation Systems | Subject: Q-series PLC
Edited by the Engineeringtalk Editorial Team on 02 September 2005

Modular PLC set to grow with business
expansion

Kingspan Building Products has installed a state of the art Mitsubishi control system to ensure optimum materials management.

Kingspan Building Products is securing production of its insulating panels by more than doubling its raw materials holding capacity at its manufacturing plant in Pembridge, Herefordshire To do this it has added 11 new chemical storage tanks to the eight existing ones and installed a state of the art Mitsubishi control system to ensure optimum materials management

Demand for insulating panels is increasing as building regulations place more and more emphasis on thermal efficiency and as builders develop new construction techniques to reduce dependency on time consuming wet trades such as plastering.

Kingspan's objective is to be able to store enough materials on site for one or two weeks' production so that delivery problems never translate into production stoppages.

Kingspan runs production as a continuous process five and a half days a week, with maintenance scheduled for the Saturday shutdown.

The finished panels consist of expanded and set foam sandwiched between aluminium-based foil sheets.

The foam is laid down as a liquid and sets or goes off when the panel is passed through an oven section.

Once solidified the panels are cut to length, usually 7m, and dispatched to the ever-hungry builders' merchants.

The base chemical from which the foam is made is MDI and this is mixed with one or more polyoils, the precise 'recipe' dictating the chemical reaction and therefore the final performance characteristics of the foam.

This mixture is held in a relatively small 'day tank' which holds enough material for several hours production.

The main storage tanks are all 50 tonne capacity and 8m tall and are supplied directly by the road tankers which bring the powders from the chemical manufacturers.

Kingspan brought in the expertise of local systems integrator Wildgoose and Davis to design, install and maintain the control system.

Partner Graham Wildgoose recalls: "There was a history of using Mitsubishi control equipment on site, and we were happy to continue this because we could see that the new system requirements could be handled very elegantly by one Mitsubishi Q-series PLC (programmable logic controller) fitted with a Q-02 CPU (central processor unit)".

Each tank is fitted with a load cell to monitor its material content, and also with a temperature probe installed as a backstop to indicate if there has been any untoward chemical reaction in the tank.

Such a reaction is highly unlikely, but could have a significant effect on production if one were not spotted promptly.

The load cells constantly feed real time data to the PLC which is running Mitsubishi's MX4 Scada (supervisory control and data acquisition) package as its main control platform.

This audits materials, usage, pipe routes and operations to provide the plant operators with up to the minute process data and information.

"The Scada communicates with the PLC via Ethernet".

"The PLC also hosts three ASI (Actuator-Sensor Interfaces) masters, as we have three separate ASI networks running around the site", says Wildgoose.

Every field device on site, including the load cells, pumps and valves, is fitted with an ASI interface and feeds into one of the networks, as it was one of the systems design objectives to reduce the amount of wiring compared with that used for the original eight-tank system.

"The Q-series is designed specifically for this sort of architecture; its modular flexibility means we can easily extend the system at a later date if necessary".

"It also means we can switch over to a standby PLC in seconds should there be a need to do so".

In fact there is a backup PLC already fitted in the main control rack and tests have shown that a complete change over can be accomplished in a matter of minutes.

The system also includes a Mitsubishi E900 HMI (human-machine interface) which provides the operators with highly sophisticated graphic representations of the tank farm and production processes.

In fact the whole plant can be run using just the PLC, HMI or Scada.

"This level of redundancy means we are unlikely to ever lose production, and also provides a very high level of safety", says Wildgoose.

Kingspan was founded as a small family firm barely 30 years ago, but now is a global organisation whose 3000 employees turn over GBP 800 million a year.

Thermal panels comprise one of its fastest developing product lines, with growth expected to continue for many years to come. Request a free brochure from Mitsubishi Electric Automation Systems ...

• Mitsubishi Electric Automation Systems: contact details and other news
• Email this article to a colleague
• Register for the free Engineeringtalk email newsletter
• Engineeringtalk Home Page

Search the Pro-Talk network of sites

Put your news on Engineeringtalk  |   Advertise  |   Get the free Engineeringtalk newsletter  |   Engineeringtalk Home
About Engineeringtalk  |   Copyright © 2000-2008 Pro-Talk Ltd, UK