Product category:
Power Supplies and Uninterruptible Power Supplies
News Release from: Puls UK | Subject: ML30 and ML50 power supply units
Edited by the Engineeringtalk Editorial
Team on 10 November 2000
Small and more economic DIN Rail Power
Supplies
The new MiniLine switched-mode power supply units, the ML30 and ML50, were developed by Puls in response to significant market requirement for small and more economic lower power units
The new MiniLine switched-mode power supply units, the ML30 and ML50, were developed by Puls in response to significant market requirement for small and more economic lower power units, and complement our existing SilverLine range (60 to 1000kWatt) Design innovations include new methods of connection using either spring clamps or plug connectors and a revamped cooling design allowing installation in different orientations
This article was originally published on Engineeringtalk on 5 Feb 2001 at 8.00am (UK)
Related stories
N+1 redundant power supplies on the DIN Rail
N+1 redundant power supplies are now available as inexpensive solutions for DIN Rail with the introduction of the SilverLine Redundancy (SLR) range from Puls
Power supply 40% smaller than corresponding units
The SL10.300 from PULS is currently the smallest 240W 3 phase power supply unit available on the market, at about 40% smaller than corresponding units of its class
Thermal considerations require minimal derating due to additional ventilation holes in the housing and sophisticated internal construction.
Power can be increased further using forced ventilation.
Excellent EMC performance (conducted and radiated) is not affected by the plastic housing and the units comply with the most stringent EMC standards EN50081, EN50082, EN60950, and EN50178.
Further reading
More developments to DIN Rail power supply
With the new SL20.310 (24-28V/20 or 25 A) Puls has now issued the latest version of its power supply classic, first introduced to the DIN-Rail market by the Munich-based company five years ago.
Power unit integrates primary and secondary fuses
Power supply specialist Puls has launched a three-phase, extremely compact 240W standard power unit which needs no fuses on the primary or secondary side and provides for unrestricted two phase use
The new 24-28V/30W and 50W power supply units are exceptionally small: w x h x d = 45 x 75 x 91 mm - comparable competitor units are twice the volume.
Fast, simple connection using new spring clamps enable the MiniLine units to be connected (or disconnected) in seconds, without the need for tools, and with complete reliability.
The spring clamp maintains constant, perpetual pressure against the cable, and, even in the toughest of conditions (such as vibration) retightening is unnecessary, and no corrosion forms at the point of contact.
There is no need for cable end sleeves (ferrules), unless required.
Alternatively, the ML50.111 (50 W) uses a plug connector with screw terminals, allowing the unit to be quickly connected or replaced without the need for rewiring.
The MiniLine series has many additional features already standard in the higher power range.
The Wide-Range-Input (100-240 V AC nominal voltage, permitted limits: 85-264 V AC/ 85-375 V DC), a wide temperature range (-10 to 70C) and approvals including the CB Scheme, UL1950, and UL508 enable their use almost anywhere in the world.
Puls Overload Design means the units do not switch off at overload, but continue to supply up to 1.5 times the rated current in order to start up heavy loads (such as motors or DC/DC converters).
This exclusive design therefore saves both unnecessary expense and valuable space.
The 50W units feature DCok signal output for remote monitoring.
Designed as a source of current, this output can directly control a 24V relay (inductive resistance > 700?) or an LED with protective resistor.
It can also be used by external logic for other control purposes, with the recovery diode needed for relay controls already built in to the unit.
Standard units can be paralleled for an increase in output power, however the ML50.101 can be used for parallel operation with load sharing.
By means of a slightly inclined 'soft output' characteristic curve (1V voltage drop between no-load operation and full load) the load is evenly distributed over the power supply units operating in parallel.
In this mode the units are more heat efficient and thus have a longer and more reliable lifespan.
• Puls UK: contact details and other news
• Email this article to a colleague
• Register for the free Engineeringtalk email newsletter
• Engineeringtalk Home Page
Search the Pro-Talk network of sites
