Torque sensor watches over test rig calibration
A
Sensor Technology product story
Edited by the Engineeringtalk editorial team
Jun 17, 2005
A dynamometer for testing 180 motors per hour for vehicle electrohydraulic power assisted steering, uses a noncontact torque transducer to ensure complete accuracy of the readings.
A dynamometer for testing 180 motors per hour for vehicle electrohydraulic power assisted steering, uses a noncontact torque transducer from Sensor Technology of Banbury to ensure complete accuracy of the readings.
Installed at a tier 1 supply company, the dynamometer forms part of a highly automated test cell that includes conveyors to deliver and remove a steady stream of motors to be tested.
A robot manipulator transfers the incoming motors onto the dynamometer and after testing loads them onto the accept or reject exit conveyor.
This level of automation is crucial for maintaining the cycle time, repeatability and validity of the tests.
Normally with a dynamometer the load is applied by a hysteresis brake and there are negligible losses between these two elements.
But in order to allow for the throughflow and handling of the motors the cell had to be arranged with the brake and dynamometer further apart than usual.
Connecting them was achieved using a longer than normal shaft and coupling.
This introduced parasitic losses into the system, which had to be accounted for if the test results were to be accurate.
An elegant solution was achieved by installing a Torqsense transducer to regularly test the torque inherent in system.
The test instruments are then calibrated to account for the measured "offset".
One of the key reasons for selecting Torqsense transducers for the test rig was that they do not need to be physically connected to the test piece via a complicated set of slip rings which would be time consuming to assemble and dismantle between each motor under test, and made the required 20 second turnaround unachievable.
The transducer used is a 1Nm 310 Series Torqsense, the baby of Sensor Technology's range.
This is an intelligent unit with all the necessary signal processing electronics built into its main body, giving it a plug-and-go capability that Dana found very attractive.
In effect a Torqsense transducer is a frequency dependent strain gauge operating at ultrasound frequencies and consists of a piezoelectric comb mounted on the test shaft to monitor variations in its resonance frequency as the torsional load varies.
An RF (radio frequency) link is used for wireless transmission of signals to an adjacent pick up so that rotation is unhindered by slip rings or to the mechanical connections.
To calibrate the cell, the dynamometer is run without a test motor to record the residual load.
The calibration routine then offsets this so that the instruments read zero ready for the first test of the day.
During predelivery tests on the rig, careful record was kept of the measured offsets.
As expected when the bearing supporting the shaft were new the offset changed markedly from day to day.
But it settled down to a near constant as the bearings wore-in.
Similar records are now kept on the production floor, which show the offset to be constant for months on end after a brief settling-in period.
However the quality standards and traceability now required by the automotive majors, make the Torqsense a vital operating part of the cell, as it removes any suggestion that the calibration is awry.
Not what you're looking for? Search the site.
Contact Sensor Technology
Tel +44 1869 238400
Other Sensor Technology stories
-
SAW-based torque transducer sets new standard
The new 310 Series Torqsense transducer is set to provide high-accuracy low-cost noncontact torque measurement of drive shafts and other rotating machine elements. -
ST offers RWT310/320 and RWT330/340 torque sensors
Sensor Technology's digital RWT310/320 torque sensors with integrated electronics and RWT330/340 torque sensors with separate electronics include the latest Torqsense (SAW) technology. -
Powertrain selects Torqsense transducer
A Torqsense transducer from Sensor Technology is a key part of a test rig designed by Powertrain Technologies to accurately measure small changes in drive torque. -
Torqsense RWT330/340 to be unveiled at M-Tec
Sensor Technology is to unveil the Torqsense RWT330/340 series of non-contact measurement sensors for space-critical applications at M-Tec 2009. -
Sensor offers Torqsense to monitor torque
Torqsense provides a non-contact method of taking torque readings.
Browse by category
-
Capital Equipment (3,423)
- Capital Equipment (1)
- Compressors and Air Treatment (519)
- Electrical hardware (131)
- Electronics Manufacturing, Tools, Instruments (192)
- Machinery and Production Equipment (1,106)
- Manufacturing Machinery and Plant Equipment (468)
- Production line blowers and fans (65)
- Robotics, Handling and Storage (941)
- Consultancy and Services (909)
-
Control and Instrumentation (5,068)
- Cabling, Conduit, Signal Conditioning (807)
- CNC and Motion Controllers (187)
- Control and Instrumentation (2)
- HMIs/Operator Interfaces (295)
- Logic Controllers, Timers and Relays (96)
- Mid-range and Large PLCs (202)
- Plant- and Machine-Wide Communications (1,185)
- Plantwide control (1,337)
- Power Supplies, Uninterruptible Power (569)
- Smaller-Sized PLCs (388)
-
Drives, Motors and Controls (3,398)
- Drives, Motors and Controls (1)
- Industrial Drives/Controls (1,285)
- Industrial Motors (500)
- Linear Drives and Motors (115)
- Precision Motors and Gears (420)
- Stepper and Servo Drives, Motors, Controls (1,075)
-
Electrical and Electronic Equipment Design (4,212)
- Batteries, chargers and circuit protection (558)
- Connectors, Terminals, Busbars, Slip Rings (695)
- Electrical and Electronic Components (636)
- Electrical and Electronic Equipment Design (1)
- Electrical and Electronic Subassemblies (371)
- Enclosures and Equipment Cooling Fans (713)
- Knobs, Handles and Enclosure Hardware (426)
- PCs and Embedded Systems (812)
-
Engineering Design Software (6,236)
- 2D CAD software (201)
- 3D CAD software (1,162)
- CAM, CNC, production management software (572)
- Data, document management software (313)
- Electrical design software (165)
- Engineering Design Software (15)
- FEA and structural analysis software (374)
- File conversion software, data capture (355)
- Fluid, thermal, noise, vibration software (334)
- Materials design and moulding design software (152)
- Maths, charting, statistics, QA software (319)
- PLM and collaboration software (652)
- Process, instrumentation, automation software (261)
- Publishing and documentation software (232)
- Rendering, visualisation, styling software (201)
- Simulation, modelling, validation software (928)
-
Engineering Industry News, Resources (6,145)
- Electronic Resources for Engineers (278)
- Engineering Business News, Views (388)
- Engineering Conferences (433)
- Engineering Education, Resources, Standards (845)
- Engineering Exhibitions, Events (568)
- Engineering Guides, Newsletters (357)
- Engineering Industry Developments, Awards (636)
- Engineering Industry News, Resources (4)
- Engineering Industry Reports, Surveys (597)
- Engineering Recruitment, Employment (219)
- Engineering Seminars (405)
- Engineering Training Courses (443)
- Health and Safety Consultancy, Software (176)
- Health and Safety Events, Training, News (280)
- Health and Safety Legislation (402)
- Health and Safety Strategy, Risk Assessment (114)
- Machine Building (4,568)
-
Materials and Processing (2,994)
- Materials and components (2,237)
- Materials and Processing (5)
- Materials processing and testing (288)
- Rapid Prototyping (464)
-
Monitoring, Measurement and Quality (5,543)
- Data Acquisition Hardware and PC I/O Boards (479)
- Data acquisition Software and Communications (498)
- Data loggers (423)
- Electrical and Electronic Testing, PAT Equipment (636)
- Form/co-ordinate, optical, vision instruments (736)
- Gauges, Indicators and Instruments (445)
- Materials testing equipment (420)
- Monitoring, Measurement and Quality (1)
- Telecomms/network test equipment, software etc (156)
- Testing and Calibration Services and Information (510)
- Testing, analysing and monitoring equipment (1,239)
-
Powertrain Design (3,652)
- Bearings (960)
- Chains and belts (329)
- Gears, brakes, couplings and engines (1,456)
- Hydraulic Components (473)
- Lubricants (431)
- Powertrain Design (2)
-
Sensors (7,150)
- Accelerometers and Vibration Sensors (434)
- Barcode Sensors (103)
- Flowmeters and Flow Sensors (622)
- Gas, Chemical, Radiation, Magnetic Sensors (286)
- Humidity and Environmental Sensors (155)
- Level Sensors and Leak Detectors (529)
- Linear Position Sensors (408)
- Loadcells, Force Sensors, Torque Sensors (712)
- Pressure sensors (625)
- Proximity Sensors (708)
- Rotary Position, Tilt and Angular Sensors (551)
- Sensors (8)
- Temperature sensors (613)
- Vision and Colour Sensors (1,396)
- Small Mechanical Components, Joining, Tools (1,989)
- Valves, Pumps, Process Hardware (3,661)
