Software sets inverters to rewind webs safely
A
Yaskawa Electric Europe product story
Edited by the Engineeringtalk editorial team
Jan 8, 2003
Yaskawa has developed special software for its range of AC inverter drives to optimise rewinding control with a quick and easy PID setup.
Rewinding in machines that use a web, such as printing and paper manufacturing or those using a warp such as in textile machines, can create problems in machine control that can lead to reduced cycle times or even web breakages.
In response to this long-standing problem, Yaskawa has developed special software for its range of AC inverter drives to optimise rewinding control with a quick and easy PID setup.
The net results of Yaskawa's development for the user are reduced acceleration and deceleration ramps, increased line speed, improved control of the winding tension, improved product quality and no web breakages even in emergency stops.
In rewinding the line speed is kept constant and a "dancer" control provides the required constant tension.
Yaskawa's inverters have a built in PID function that controls the dancer response by adjusting the motor speed.
However, the PID control loop must be carefully adjusted to minimise oscillation and obtain the highest possible line speed.
To keep a constant line speed as the diameter of the reel increases, the motor speed clearly must decrease.
This creates a problem in that as the reel diameter increases the dancer position error feedback tries to compensate using the same output frequency (speed) adjustment as it used for the smaller diameter reel.
This causes instability and it is clear why when one considers that if the rear reel diameter is, say, 10cm, a 5Hz change in frequency causes a 5m/min line speed increase.
Similarly, if the rear reel is 100cm diameter, a 5Hz change in frequency creates a 50m/min line speed increase.
Hence, if the PID gain is set to be optimised for the smallest reel diameter, it is potentially unstable when the reel is at full capacity and vice versa.
At the same time, if the rewinder speed is ramped up or down, the high PID gain settings cause an overshoot of the dancer and this can be sufficient to break the web.
Yaskawa's software enables the inverter's output frequency to be set inversely proportional to the reel diameter.
To do this, the software provides two P gain settings, the first for the minimum frequency and second for the maximum.
The actual gain is therefore linear between these two points and thus provides the optimum gain settings for the entire speed range.
If the machine speed is ramped up, the gain remains low and the chance of dancer overshoot is minimised.
At the required speed, the high gain controls the dancer position with highly stable response.
The Yaskawa drive's control software increases productivity (line speed), improves quality (the dancer controls the line tension better) and obviates downtime (the dancer control remains stable).
Not what you're looking for? Search the site.
Contact Yaskawa Electric Europe
Tel +49 6196 569 300
Other Yaskawa Electric Europe stories
-
Yaskawa to showcase high-speed handling system
Yaskawa will exhibit its F20-F35 high-speed pick-and-place solution at the Motek 2009 trade show in Stuttgart, Germany. -
Yaskawa offers small-component assembly system
Yaskawa has introduced the F50-G253 electrically driven small-component assembly system, which features a highly dynamic positioning action coupled with absolute precision. -
Yaskawa to show SGT integrated linear slider axis
Yaskawa will introduce a ready-to-install SGT integrated linear slider axis at the Motek trade fair in Stuttgart, Germany. -
Yaskawa introduces plug-and-play gantry system
Yaskawa has introduced a gantry system to enable the simple, rapid integration of linear motors into the manufacturing process, saving time and money. -
Motion controller has sequence control
The Yaskawa Electric motion controller MP2300Siec offers PLC sequence control and different motion control functions on a single platform.
Browse by category
-
Capital Equipment (3,495)
- Capital Equipment (1)
- Compressors and Air Treatment (534)
- Electrical hardware (131)
- Electronics Manufacturing, Tools, Instruments (192)
- Machinery and Production Equipment (1,125)
- Manufacturing Machinery and Plant Equipment (474)
- Production line blowers and fans (73)
- Robotics, Handling and Storage (965)
- Consultancy and Services (919)
-
Control and Instrumentation (5,108)
- Cabling, Conduit, Signal Conditioning (813)
- CNC and Motion Controllers (188)
- Control and Instrumentation (2)
- HMIs/Operator Interfaces (296)
- Logic Controllers, Timers and Relays (96)
- Mid-range and Large PLCs (203)
- Plant- and Machine-Wide Communications (1,197)
- Plantwide control (1,350)
- Power Supplies, Uninterruptible Power (573)
- Smaller-Sized PLCs (390)
-
Drives, Motors and Controls (3,428)
- Drives, Motors and Controls (2)
- Industrial Drives/Controls (1,290)
- Industrial Motors (501)
- Linear Drives and Motors (119)
- Precision Motors and Gears (428)
- Stepper and Servo Drives, Motors, Controls (1,086)
-
Electrical and Electronic Equipment Design (4,280)
- Batteries, chargers and circuit protection (576)
- Connectors, Terminals, Busbars, Slip Rings (711)
- Electrical and Electronic Components (647)
- Electrical and Electronic Equipment Design (3)
- Electrical and Electronic Subassemblies (374)
- Enclosures and Equipment Cooling Fans (720)
- Knobs, Handles and Enclosure Hardware (428)
- PCs and Embedded Systems (821)
-
Engineering Design Software (6,326)
- 2D CAD software (202)
- 3D CAD software (1,180)
- CAM, CNC, production management software (576)
- Data, document management software (321)
- Electrical design software (165)
- Engineering Design Software (17)
- FEA and structural analysis software (376)
- File conversion software, data capture (358)
- Fluid, thermal, noise, vibration software (338)
- Materials design and moulding design software (152)
- Maths, charting, statistics, QA software (324)
- PLM and collaboration software (659)
- Process, instrumentation, automation software (269)
- Publishing and documentation software (234)
- Rendering, visualisation, styling software (206)
- Simulation, modelling, validation software (949)
-
Engineering Industry News, Resources (6,200)
- Electronic Resources for Engineers (278)
- Engineering Business News, Views (388)
- Engineering Conferences (435)
- Engineering Education, Resources, Standards (849)
- Engineering Exhibitions, Events (575)
- Engineering Guides, Newsletters (365)
- Engineering Industry Developments, Awards (636)
- Engineering Industry News, Resources (4)
- Engineering Industry Reports, Surveys (597)
- Engineering Recruitment, Employment (219)
- Engineering Seminars (414)
- Engineering Training Courses (457)
- Health and Safety Consultancy, Software (180)
- Health and Safety Events, Training, News (285)
- Health and Safety Legislation (403)
- Health and Safety Strategy, Risk Assessment (115)
- Machine Building (4,606)
-
Materials and Processing (3,021)
- Materials and components (2,259)
- Materials and Processing (5)
- Materials processing and testing (291)
- Rapid Prototyping (466)
-
Monitoring, Measurement and Quality (5,624)
- Data Acquisition Hardware and PC I/O Boards (486)
- Data acquisition Software and Communications (503)
- Data loggers (425)
- Electrical and Electronic Testing, PAT Equipment (641)
- Form/co-ordinate, optical, vision instruments (757)
- Gauges, Indicators and Instruments (448)
- Materials testing equipment (430)
- Monitoring, Measurement and Quality (1)
- Telecomms/network test equipment, software etc (158)
- Testing and Calibration Services and Information (518)
- Testing, analysing and monitoring equipment (1,257)
-
Powertrain Design (3,698)
- Bearings (976)
- Chains and belts (333)
- Gears, brakes, couplings and engines (1,470)
- Hydraulic Components (474)
- Lubricants (441)
- Powertrain Design (3)
-
Sensors (7,249)
- Accelerometers and Vibration Sensors (447)
- Barcode Sensors (103)
- Flowmeters and Flow Sensors (638)
- Gas, Chemical, Radiation, Magnetic Sensors (289)
- Humidity and Environmental Sensors (157)
- Level Sensors and Leak Detectors (537)
- Linear Position Sensors (412)
- Loadcells, Force Sensors, Torque Sensors (725)
- Pressure sensors (635)
- Proximity Sensors (711)
- Rotary Position, Tilt and Angular Sensors (559)
- Sensors (10)
- Temperature sensors (621)
- Vision and Colour Sensors (1,405)
- Small Mechanical Components, Joining, Tools (2,027)
- Valves, Pumps, Process Hardware (3,713)
